From: J.Vieira ([email protected])
Date: Fri Dec 15 2000 - 12:16:04 CET
Hello small World of MuLinux!
No Way my friend! Neither forcing io=0xd000 nor with io=''.
BTW, whynot to do a fun addon with all that sound stuff (mpg123 ...) and
reserving space for some game or more...
Vieira
Linux User 100.600
-----Mensagem original-----
De: Bob Romprey [mailto:[email protected]]
Enviada em: sexta-feira, 15 de dezembro de 2000 03:18
Para: [email protected]
Assunto: RE: RES: mu SETUP
Try filling in the io and IRQ parameters when doing the setup with "" rather
than the '' as suggested in the setup text.......I experienced the same
problem today using a 3c509b card.........replaced '' with "" and it works
just fine now.
the "" represents an empty string.
winsor
>Reply-To: [email protected]
>From: "J.Vieira" <[email protected]>
>To: <[email protected]>
>Subject: RES: mu SETUP
>Date: Fri, 15 Dec 2000 01:10:31 -0200
>
>Hello small World of MuLinux
>
>I get the same error "Symbol 'io' not found" trying to use my ne2k-pci on
>mu10r5
>
>I´ve already seem this film!!!
>
>Jose Vieira
>Linux User 100.600
>
>
>-----Mensagem original-----
>De: Jos? Luis G?mez Dans
>[mailto:[email protected]]Em nome de José Luis
>Gómez Dans
>Enviada em: quinta-feira, 14 de dezembro de 2000 15:15
>Para: [email protected]
>Assunto: Re: mu SETUP
>
>
>On Thu, Dec 14, 2000 at 07:06:40PM +0100, Christian Bourgeois wrote:
>> > If I well remember, it is based on a rtl8139 chip, so it should work
>with
>> > rtl8139 netword module.
>
> Note that this is a PCI card...
>
>> > But,
>> >
>> > when "setup eth0 CARD=rtl8139 IRQ=5 IO=0xE000 IP=192.168.0.203" i
always
>> > get the error "Symbol 'io' not found" !!!
>> > I haven't figured out where the problem comes from.
>> >
>> > Before installing mulinux on the computer, I had tested it
>> > with floppy disks (with SRV only, not WKS), and it worked fine with
that
>> > card. But is was not the last version, it was the 11r1 I think.
>
> There's no IO or IRQ for a PCI card. If you just do
>insmod rtl8139, you would be alright. I don't have mu at hand, but you
>don't what to have any IO or IRQ for thsi card
>
>> > I tested the above hard disk installation with the 10r5 and 11r2, and
>both
>> > give the same error.
>> >
>>
>> Do you have any idea ?
>> It'll be very helpfull, as I'm going to install it on about 25 computers
>!!!
>>
>> Also, is there any way to protect the "C:\LINUX" from being modified when
>in
>> DOS mode ?
>>
>> Thanks a lot,
>>
>> Cheers,
>> Christian.
>>
>>
>> ---------------------------------------------------------------------
>> To unsubscribe, e-mail: [email protected]
>> For additional commands, e-mail: [email protected]
>
>--
>José L Gómez Dans PhD student
>Tel: +44 114 222 5582 Radar & Communications Group
>FAX; +44 870 132 2990 Department of Electronic Engineering
> University of Sheffield UK
>
>---------------------------------------------------------------------
>To unsubscribe, e-mail: [email protected]
>For additional commands, e-mail: [email protected]
>
>
>
>---------------------------------------------------------------------
>To unsubscribe, e-mail: [email protected]
>For additional commands, e-mail: [email protected]
------------------------------------------------------------
Visit the world's greatest site at http://www.farts.com and listen to the
fart
of the day. Also, get your very own farts.com E-mail account. FREE!!!!!
---------------------------------------------------------------------
To unsubscribe, e-mail: [email protected]
For additional commands, e-mail: [email protected]
---------------------------------------------------------------------
To unsubscribe, e-mail: [email protected]
For additional commands, e-mail: [email protected]
This archive was generated by hypermail 2.1.6 : Sat Feb 08 2003 - 15:27:17 CET